Engineering fit
 |
Fit refers to the mating of two mechanical components. Manufactured parts are very frequently required to mate with one another. They may be designed to slide freely against one another or they may be designed to bind together to form a single unit. The most common fit found in the machine shop is that of a shaft in a hole.
There are three general categories of fits: 1) Clearance fits for when it may be desirable for the shaft to rotate or slide freely within the hole, this is usually referred to as a "sliding fit." 2) Interference fits for when it is desirable for the shaft to be securely held within the hole, this is usually referred to as an interference fit and 3) Transition fits for when it is desirable that the shaft to be held securely, yet not so securely that it cannot be disassembled, this is usually referred to as a Location or Transition fit.
Within each category of fit there are several classes ranging from high precision and narrow tolerance (allowance) to lower precision and wider tolerance. The choice of fit is dictated first by the use and secondly by the manufacturability of the parts.
Interference fits
An Interference Fit, also known as a Press Fit or Friction Fit, is a fastening between two parts which is achieved by friction after the parts are pushed together, rather than by any other means of fastening.
Shrink fits
Example = wheel belts,tyres,coupling under certain conditions
Force fits
FN 1 to FN 5
Transition fits
LC 1 to LC 11 LT 1 to LT 6 LN 1 to LN 3
RC1: Close Sliding Fits
This kind of fits are intended for the accurate location of parts which must assemble without noticeable play.
RC2: Sliding Fits
This kind of fits are intended for the accurate location but with greater maximum clearance than class RC1. Parts made to this fit turn and move easily. This type is not designed for free run. Sliding fits in larger sizes may seize with small temperature changes.
RC3: Precision Running Fits
This kind of fits are about the closest fits which can be expected to run freely. Precision running fits are intended for precision work at low speed, low bearing pressures, and light journal pressures. RC3 is not suitable where noticeable temperature differences occur.
RC4: Close Running Fits
This kind of fits are mostly for running fits on accurate machinery with moderate surface speed, bearing pressures, and journal pressures where accurate location and minimum play are desired. This kind of fits also can be described as smaller clearances with higher requirements for precision fit.
RC5 and R6: Medium Running Fits
This kind of fits are designed for machines running at higher running speeds, considerable bearing pressures, and heavy journal pressure. This kind of fits also can be described with greater clearances with common requirements for fit precision.
RC7: Free Running Fits
This kind of fits are intended to use where accuracy is not essential. It is suitable for great temperature variations. This fits are suitable to use without any special requirements for precise guiding of shafts.
RC8 and RC9: Loose Running Fits
This kind of fits are intended for use where wide commercial tolerances may be required on the shaft. With this fits, The parts with great clearances with having great tolerances. Loose running fits exposed to effects of corrosion, contamination by dust and thermal or mechanical deformations.
ISO Metric fits
ISO-R286 and ANSI B4.2-1978
Fitting
The task of fitting is one of making skilled cuts to parts, on a cut-and-try basis (cut, try; cut more, try again), so that they will fit together with the desired degree of fit. Prior to the advent of interchangeable manufacture, fitting was the only way to create precise assemblies, such as the locks of firearms, and it was done manually, one assembly at a time, with tools such as files and laps. The person who did the fitting could be a craftsman such as a gunsmith, or a factory worker at a bench (called a fitter), or a toolmaker or toolfitter. When interchangeable manufacture began, its first form was one that did not obviate fitting, but simply shifted its locus, from the fitting of mating parts to each other, to the fitting of identical parts to a jig, template, or gauge ("filing to jig", "filing to gauge"). Gradually, manufacturing technology transitioned ever more toward processes in which parts were machined in such a precise, repeatable way that they required no fitting at all. For example, a pistol's hammer could be milled with a milling machine directly to gauge size, rather than being rough-milled to nearly that size followed by hand filing to gauge.
See also
References
- ^ http://www.cobanengineering.com/Tolerances/ANSILimitsAndFits.asp. Retrieved 9 September 2013.
{{cite web}}: Missing or empty|title=(help)