Metrication

A speedometer used in American and British cars, showing the speed of the vehicle in miles per hour (outer, in white) and kilometres per hour (inner, in red) – for Canadian vehicles the scales are reversed, or in km/h only.

A speedometer from an Australian car, showing the speed of the vehicle only in km/h, as in almost all countries.

Metrication or metrification is the act or process of converting the system of measurement traditionally used in a country to the metric system. All over the world, nations have transitioned from their local and traditional units of measurement to the metric system. This process first began in France during the 1790s and continues more than two centuries later, and the metric system has not been fully adopted in all countries and sectors.

Overview

Most countries have the metric system as their official system of weights and measures. Some have adopted it as their official system but have not yet completed the process of metrication. Some others have not made any commitment to adopting it. There is not a general consensus in the sources as to the number of countries that fall into each of these categories.

According to Vera in a 2011 PhD dissertation, as of 2010, a total of 7 countries had not "adopted the metric system as their exclusive system of measurement". They are: Federated States of Micronesia, Liberia, Marshall Islands, Myanmar, Palau, Samoa, and the United States. According to the US Central Intelligence Agency's online The World Factbook (2016), the only countries that have not adopted the metric system are Myanmar (also known as Burma), Liberia and the US. According to Vera, the United States (and its associated states: the Federated States of Micronesia, Marshall Islands and Palau) officially use US customary units. According to a Liberian journalist, Liberia uses US customary units too. According to Vera, Samoa has never officially adopted metric system per lack of resources and expertise. According to the Liberian journalist, Liberia is committed to adopting the metric system in the future. Some sources now identify Liberia as metric, and the government of Myanmar has stated that the country would metricate with a goal of completion by 2019. Both Myanmar and Liberia are substantially metric countries, trading internationally in metric units.

Some countries such as Guyana, adopted the metric system, but have had some trouble over time implementing it. Antigua and Barbuda, also "officially" metric, is moving toward total implementation of the metric system, but more slowly than expected. The government had announced that they have plans to convert their country to the metric system by the first quarter of 2015. Other Caribbean countries such as Saint Lucia are officially metric but are still in the process toward full conversion. In the United Kingdom the metric system is the official system for most regulated trading by weight or measure purposes, but some imperial units remain the primary official unit of measurement. As of 2018 the UK has only partially metricated.

The European Union used the Units of Measure Directive to attempt to achieve a common system of weights and measures and to facilitate the European Single Market. Throughout the 1990s, the European Commission helped accelerate the process for member countries to complete their metric conversion processes. Among them was the United Kingdom where laws in some or all contexts mandate or permit many imperial measures, such as miles and yards for road-sign distances, road speed limits in miles per hour, pints of beer, and inches for clothes. The United Kingdom secured permanent exemptions for the mile and yard in road markings, and (with Ireland) for the pint (Imperial) of draught beer sold in pubs (see Metrication in the United Kingdom). In 2007, the European Commission also announced that (to appease British public opinion and to facilitate trade with the United States) it was to abandon the requirement for metric-only labelling on packaged goods, and to allow dual metric–imperial marking to continue indefinitely.

The United States, the United Kingdom, and Canada have some active opposition to metrication, particularly where updated weights and measures laws would make obsolete historic systems of measurement.

Before the metric system

Further information: History of measurement

The Roman empire used the pes (foot) measure. This was divided into 12 unciae ("inches"). The libra ("pound") was another measure that had wide effect on European weight and currency long after Roman times, e.g. lb, £. The measure came to vary greatly over time. Charlemagne was one of several rulers who launched reform programmes of various kinds to standardise units for measure and currency in his empire, but there was no real general breakthrough.

In medieval Europe, local laws on weights and measures were set by trade guilds on a city-by-city basis. For example, the ell or elle was a unit of length commonly used in Europe, but its length varied from 40.2 centimetres in one part of Germany to 70 centimetres in The Netherlands and 94.5 centimetres in Edinburgh. A survey of Switzerland in 1838 revealed that the foot had 37 different regional variations, the ell had 68, there were 83 different measures for dry grain, 70 measures for fluids and 63 different measures for "dead weights". When Isaac Newton wrote Philosophiae Naturalis Principia Mathematica in 1687, he quoted his measurements in Parisian feet so readers could understand the size. Examples of efforts to have local intercity or national standards for measurements include the Scottish law of 1641, and the British standard imperial system of 1824, which is still commonly used in the United Kingdom. At one time Imperial China had successfully standardised units for volume throughout its territory, but by 1936 official investigations uncovered 53 values for the chi varying from 200 millimetres to 1250 millimetres; 32 values of the cheng, between 500 millilitres and 8 litres; and 36 different tsin ranging from 300 grams to 2500 grams. However, revolutionary France was to produce the definitive International System of Units which has come to be used by most of the world today.

The desire for a single international system of measurement came from increasing international trade and the need to apply common standards to goods. For a company to buy a product produced in another country, they need to ensure that the product would arrive as described. The medieval ell was abandoned in part because its value could not be standardised. One primary advantage of the International System of Units is simply that it is international, and the pressure on countries to conform to it grew as it became increasingly the international standard. It also simplified the teaching and learning of measurement as all SI units are based on a handful of base units (in particular, the metre, kilogram and second cover the majority of everyday measurements), using decimal prefixes to cover all magnitudes. This contrasts with pre-metric units, which largely have names that do not relate directly to one another (e.g. inch, foot, yard, mile) and are related to one another by inconsistent ratios which must be memorised (e.g. 12, 3, 1760). As the values in an SI expression are always decimal (i.e. without vulgar fractions) and mixed units (such as "feet and inches") are not used with SI, measurements are easy to add and multiply. Scientific measurement and calculation are greatly simplified as the units for electricity, force etc. are part of the SI system and hence are all interrelated in a coherent manner (e.g. 1 J = 1 kg·m²·s⁻² = 1 V·A·s). Standardisation of measures has contributed significantly to the industrial revolution and technological development in general. SI is not the only example of international standardisation; several powerful international standardisation organisations exist for various industries, such as the International Organisation for Standardisation (ISO), the International Electrotechnical Commission (IEC), and the International Telecommunication Union (ITU).

Forerunners of the metric system

Decimal numbers are an essential part of the metric system, with only one base unit and multiples created on the decimal base, the figures remain the same. This simplifies calculations. Although the Indians used decimal numbers for mathematical computations, it was Simon Stevin who in 1585 first advocated the use of decimal numbers for everyday purposes in his booklet De Thiende (Middle Dutch for 'The Tenth'). He also declared that it would only be a matter of time before decimal numbers were used for currencies and measurements. His notation for decimal fractions was clumsy, but this was overcome with the introduction of the decimal point, generally attributed to Bartholomaeus Pitiscus who used this notation in his trigonometrical tables (1595).

In 1670, Gabriel Mouton published a proposal that was in essence similar to Wilkins' proposal, except that his base unit of length would have been 1/1000 of a minute of arc (about 1.852 m) of geographical latitude. He proposed calling this unit the virga. Rather than using different names for each unit of length, he proposed a series of names that had prefixes, rather like the prefixes found in SI.

In 1790, Thomas Jefferson submitted a report to the United States Congress in which he proposed the adoption of a decimal system of coinage and of weights and measures. He proposed calling his base unit of length a "foot" which he suggested should be either 3⁄10 or 1⁄3 of the length of a pendulum that had a period of one second – that is 3⁄10 or 1⁄3 of the "standard" proposed by Wilkins over a century previously. This would have equated to 11.755 English inches (29.8 cm) or 13.06 English inches (33.1 cm). Like Wilkins, the names that he proposed for multiples and subunits of his base units of measure were the names of units of measure that were in use at the time. The great interest in geodesy during this era, and the measurement system ideas that developed, influenced how the continental US was surveyed and parceled. The story of how Jefferson's full vision for the new measurement system came close to displacing the Gunter chain and the traditional acre, but ended up not doing so, is explored in Andro Linklater's Measuring America.

Adoption of metric weights and measures

During the nineteenth century the metric system of weights and measures proved a convenient political compromise during the unification processes in the Netherlands, Germany and Italy. In 1814, Portugal became the first country not part of the French Empire to officially adopt the metric system. Spain found it expedient in 1858 to follow the French example and within a decade Latin America had also adopted the metric system, or had already adopted the system, such as the case of Chile by 1848. There was considerable resistance to metrication in the United Kingdom and in the United States, but once the United Kingdom announced its metrication program in 1965, the Commonwealth followed suit.

France

Napoleon Bonaparte introduced the Mesures usuelles.

The introduction of the metric system into France in 1795 was done on a district by district basis with Paris being the first district. By modern standards the transition was poorly managed. Although thousands of pamphlets were distributed, the Agency of Weights and Measures who oversaw the introduction underestimated the work involved. Paris alone needed 500,000 metre sticks, yet one month after the metre became the sole legal unit of measure, they only had 25,000 in store. This, combined with other excesses of the Revolution and the high level of illiteracy made the metric system unpopular.

Napoleon himself ridiculed the metric system, but as an able administrator, recognised the value of a sound basis for a system of measurement and under the décret impérial du 12 février 1812 (imperial decree of 12 February 1812), a new system of measure – the mesures usuelles ("customary measures") was introduced for use in small retail businesses – all government, legal and similar works still had to use the metric system and the metric system continued to be taught at all levels of education. The names of many units used during the ancient regime were reintroduced, but were redefined in terms of metric units. Thus the toise was defined as being two metres with six pieds making up one toise, twelve pouces making up one pied and twelve lignes making up one pouce. Likewise the livre was defined as being 500 g, each livre comprising sixteen once and each once eight gros and the aune as 120 centimetres.

By means of the La loi du 4 juillet 1837 (the law of 4 July 1837), Louis Philippe I effectively revoked the use of mesures uselles by reaffirming the laws of measurement of 1795 and 1799 to be used from 1 May 1840. However, many units of measure, such as the livre (for half a kilogram), remained in everyday use for many years, and to a residual extent up to this day.

Germany

Stone marking the Austro-Hungarian/Italian border at Pontebba displaying myriametres (10 km), a unit used in Central Europe in the 19th century.

At the outbreak of the French Revolution, much of modern-day Germany and Austria were part of the Holy Roman Empire which had become a loose federation of kingdoms, principalities, free cities, bishoprics and other fiefdoms, each with its own system of measurement, though in most cases the systems were loosely derived from the Carolingian system instituted by Charlemagne a thousand years earlier.

During the Napoleonic era, some of the German states moved to reform their systems of measurement using the prototype metre and kilogram as the basis of the new units. Baden, in 1810, for example, redefined the Ruthe (rods) as being 3.0 m exactly and defined the subunits of the Ruthe as 1 Ruthe = 10 Fuß (feet) = 100 Zoll (inches) = 1,000 Linie (lines) = 10,000 Punkt (points) while the Pfund was defined as being 500 g, divided into 30 Loth, each of 16.67 g. Bavaria, in its reform of 1811, trimmed the Bavarian Pfund from 561.288 g to 560 g exactly, consisting of 32 Loth, each of 17.5 g while the Prussian Pfund remained at 467.711 g.

After the Congress of Vienna there was a degree of commercial cooperation between the various German states resulting in the German Customs Union (Zollverein). There were, however, still many barriers to trade until Bavaria took the lead in establishing the General German Commercial Code in 1856. As part of the code the Zollverein introduce the Zollpfund (Customs Pound) which was defined to be exactly 500 g and which could be split into 30 'lot'. This unit was used for inter-state movement of goods, but was not applied in all states for internal use.

Although the Zollverein collapsed after the Austro-Prussian War of 1866, the metric system became the official system of measurement in the newly formed German Empire in 1872 and of Austria in 1875. The Zollpfund ceased to be legal in Germany after 1877.

Italy

Tablet showing conversions of legacy units of weights and measures to metric units, Vicopisano, Tuscany

The Cisalpine Republic, a North Italian republic set up by Napoleon in 1797 with its capital at Milan first adopted a modified form of the metric system based in the braccio cisalpino (Cisalpine cubit) which was defined to be half a metre. In 1802 the Cisalpine Republic was renamed the Italian Republic, with Napoleon as its head of state. The following year the Cisalpine system of measure was replaced by the metric system.

In 1806, the Italian Republic was replaced by the Kingdom of Italy with Napoleon as its emperor. By 1812, all of Italy from Rome northwards was under the control of Napoleon, either as French Departments or as part of the Kingdom of Italy ensuring the metric system was in use throughout this region.

After the Congress of Vienna, the various Italian states reverted to their original system of measurements, but in 1845 the Kingdom of Piedmont and Sardinia passed legislation to introduce the metric system within five years. By 1860, most of Italy had been unified under the King of Sardinia Victor Emmanuel II and under Law 132 of 28 July 28, 1861 the metric system became the official system of measurement throughout the kingdom. Numerous Tavole di ragguaglio (Conversion Tables) were displayed in shops until 31 December 1870.

Netherlands

The Netherlands (as the revolutionary Batavian Republic) began to use the metric system from 1799 but, as with its co-revolutionaries in France, encountered numerous practical difficulties. Subsequently, as part of the First French Empire since 1809, the Netherlands used Napoloeon's mesures usuelles from their introduction in 1812 until the fall of his Empire in 1815. Under the (Dutch) Weights and Measures Act of 21 August 1816 and the Royal decree of 27 March 1817 (Koningklijk besluit van den 27 Maart 1817), the newly formed Kingdom of the Netherlands abandoned the mesures usuelles in favour of the "Dutch" metric system (Nederlands metrisch stelsel) in which metric units were simply given the names of units of measure that were then in use. Examples include the ons (ounce) which was defined as being 100 g.

Norway

In 1875, Norway was the first country to ratify the metre convention, and it was seen as an important step for Norway to gain independence. The decision to adopt the metric system is said to have been the Norwegian Parliament's fastest decision in peace time.

Portugal

In August 1814, Portugal officially adopted the metric system but with the names of the units substituted by Portuguese traditional ones. In this system the basic units were the mão-travessa (hand) = 1 decimetre (10 mão-travessas = 1 vara (yard) = 1 metre), the canada = 1 liter and the libra (pound) = 1 kilogram.

Spain

Until the ascent of the Bourbon monarchy in Spain in 1700, each region of Spain had its own system of measurement. The new Bourbon monarchy tried to centralise control and with it the system of measurement. There were debates regarding the desirability of retaining the Castilian units of measure or, in the interests of harmonisation, adopting the French system. Although Spain assisted Méchain in his meridian survey, the Government feared the French revolutionary movement and reinforced the Castilian units of measure to counter such movements. By 1849 however, it proved difficult to maintain the old system and in that year the metric system became the legal system of measure in Spain.

Don Carlos Ibáñez e Ibáñez de Ibero, Marquis of Mulhacén

The Spanish Royal Academy of Science urged the Government to approve the creation of a large-scale map of Spain in 1852. The following year Carlos Ibáñez e Ibáñez de Ibero was appointed to undertake this task. All the scientific and technical material had to be created. Ibáñez e Ibáñez de Ibero and Saavedra went to Paris to supervise the production by Brunner of a measuring instrument which they had devised and which they later compared with Borda's double-toise N°1 which was the main reference for measuring all geodetic bases in France and whose length was 3.8980732 metres.

In 1865 the triangulation of Spain was connected with that of Portugal and France. In 1866 at the conference of the Association of Geodesy in Neuchâtel, Ibáñez announced that Spain would collaborate in remeasuring the French meridian arc. In 1879 Ibáñez and François Perrier (representing France) completed the junction between the geodetic network of Spain and Algeria and thus completed the measurement of the French meridian arc which extended from Shetland to the Sahara.

In 1867 Russia, Spain and Portugal joined the "Europäische Gradmessung" (European Arc Measurement which would become the International Association of Geodesy). This same year at the second general conference of the European Arc Measurement held in Berlin, the question of an international standard unit of length was discussed in order to combine the measurements made in different countries to determine the size and shape of the Earth. The conference recommended the adoption of the metre and the creation of an international metre commission, according to the proposal of Johann Jacob Baeyer, Adolphe Hirsch and Carlos Ibáñez e Ibáñez de Ibero.

In November 1869 the French government issued invitations to join this commission. Spain accepted and Carlos Ibáñez e Ibáñez de Ibero took part in the Committee of preparatory research from the first meeting of the International Metre Commission in 1870. He became president of the permanent Committee of the International Metre Commission in 1872. In 1874 he was elected as president of the Permanent Commission of the European Arc Measurement. He also presided the General Conference of the European Arc Measurement held in Paris in 1875, when the association decided the creation of an international geodetic standard for the bases' measurement. He represented Spain at the 1875 conference of the Metre Convention, which was ratified the same year in Paris. The Spanish geodesist was elected as the first president of the International Committee for Weights and Measures. His activities resulted in the distribution of a platinum and iridium prototype of the metre to all States parties to the Metre Convention during the first meeting of the General Conference on Weights and Measures in 1889. Theses prototypes defined the metre right up until 1960.

United Kingdom

In 1824 the Weights and Measures Act imposed one standard 'imperial' system of weights and measures on the British Empire. The effect of this act was to standardise existing British units of measure rather than to align them with the metric system.

During the next eighty years a number of Parliamentary select committees recommended the adoption of the metric system, each with a greater degree of urgency, but Parliament prevaricated. A Select Committee report of 1862 recommended compulsory metrication, but with an "Intermediate permissive phase"; Parliament responded in 1864 by legalising metric units only for 'contracts and dealings'. The United Kingdom initially declined to sign the Treaty of the Metre, but did so in 1883. Meanwhile, British scientists and technologists were at the forefront of the metrication movement – it was the British Association for the Advancement of Science that promoted the CGS system of units as a coherent system and it was the British firm Johnson Matthey that was accepted by the CGPM in 1889 to cast the international prototype metre and kilogram.

In 1895 another Parliamentary select committee recommended the compulsory adoption of the metric system after a two-year permissive period. The 1897 Weights and Measures Act legalised the metric units for trade, but did not make them mandatory. A bill to make the metric system compulsory in order to enable the British industrial base to fight off the challenge of the nascent German base passed through the House of Lords in 1904, but did not pass in the House of Commons before the next general election was called. Following opposition by the Lancashire cotton industry, a similar bill was defeated in 1907 in the House of Commons by 150 votes to 118.

In 1965 the UK began an official programme of metrication that, as of 2024, has not been completed.

In the United Kingdom metric is the official system for most regulated trading by weight or measure purposes, but some imperial units remain the primary official unit of measurement. For example, miles, yards, and feet remain the official units for road signage – and use of imperial units is widespread. The Imperial pint also remains a permitted unit for milk in returnable bottles and for draught beer and cider in British pubs. Imperial units are also legal for use alongside metric units on food packaging and price indications for goods sold loose, and may be used exclusively where a product is sold by description, rather than by weight/mass/volume. E.g. Television screen and clothing sizes tend to be denominated in inches only, but a piece of material priced per inch would be unlawful unless the metric price was also shown.

United States

Main article: Metrication in the United States

In 1805 a Swiss geodesist Ferdinand Rudolph Hassler brought copies of the French metre and kilogram to the United States. In 1830 the Congress decided to create uniform standards for length and weight in the United States. Hassler was mandated to work out the new standards and proposed to adopt the metric system. The Congress opted for the British Parliamentiary Standard from 1758 and the Troy Pound of Great Britain from 1824 as length and weight standards. Nevertheless the primary baseline of the US Coast Survey was measured in 1834 at Fire Island using four two-metre iron bars constructed after Hassler's specification in the United Kingdom and brought back in the United States in 1815. All distances measured in the US National Geodetic Survey were referred to the metre. In 1866 the United States Congress passed a bill making it lawful to use the metric system in the United States. The bill, which was permissive rather than mandatory in nature, defined the metric system in terms of customary units rather than with reference to the international prototype metre and kilogram. By 1893, the reference standards for customary units had become unreliable. Moreover, the United States, being a signatory of the Metre Convention was in possession of national prototype metres and kilograms that were calibrated against those in use elsewhere in the world. This led to the Mendenhall Order which redefined the customary units by referring to the national metric prototypes, but used the conversion factors of the 1866 act. In 1896 a bill that would make the metric system mandatory in the United States was presented to Congress. Twenty-three of the 29 people who gave evidence before the congressional committee who were considering the bill were in favor of it, but six were against. Four of these six dissenters represented manufacturing interests and the other two were from the United States Revenue service. The grounds cited were the cost and inconvenience of the change-over. The bill was not enacted. Subsequent bills suffered a similar fate.

The United States mandated the acceptance of the metric system in 1866 for commercial and legal proceedings, without displacing their customary units. The non-mandatory nature of the adoption of the SI has resulted in a much slower pace of adoption in the US than in other countries.

In 1971 the US National Bureau of Standards completed a three-year study of the impact of increasing worldwide metric use on the US. The study concluded with a report to Congress entitled A Metric America – A Decision Whose Time Has Come. Since then metric use has increased in the US, principally in the manufacturing and educational sectors. Public Law 93-380, enacted 21 August 1974, states that it is the policy of the US to encourage educational agencies and institutions to prepare students to use the metric system of measurement with ease and facility as a part of the regular education program. On 23 December 1975, President Gerald Ford signed Public Law 94-168, the Metric Conversion Act of 1975. This act declares a national policy of coordinating the increasing use of the metric system in the US. It established a US Metric Board whose functions as of 1 October 1982 were transferred to the Dept of Commerce, Office of Metric Programs, to coordinate the voluntary conversion to the metric system.

In January 2007 NASA decided to use metric units for all future moon missions, in line with the practice of other space agencies.

Other English-speaking countries

The British metrication programme signalled the start of metrication programmes elsewhere in the Commonwealth, though India had started its programme in 1959, six years before the United Kingdom. South Africa (then not a member of the Commonwealth) set up a Metrication Advisory Board in 1967, New Zealand set up its Metric Advisory Board in 1969, Australia passed the Metric Conversion Act in 1970 and Canada appointed a Metrication Commission in 1971. Metrication in Australia, New Zealand and South Africa was essentially complete within a decade, while metrication in India and Canada is not complete. In Canada, the square foot is still widespread for commercial and residential advertisements and partially in construction because of the close trade relations with the United States. The railways of Canada continue to measure their trackage in miles and speed limits in miles per hour because they also operate in the United States. Most other Commonwealth countries adopted the metric system during the 1970s.

Apart from the United Kingdom, countries using the imperial system completed official metrication during the second half of the 20th century or the first decade of the 21st century. The most recent to complete this process was the Republic of Ireland, which began metric conversion in the 1970s and completed it in early 2005.

Conversion process

The metric system was officially introduced in France in December 1799. In the 19th century, the metric system was adopted by almost all European countries: Portugal (1814); Netherlands, Belgium and Luxembourg (1820); Switzerland (1835); Spain (1850s); Italy (1861); Romania (1864); Germany (1870, legally from 1 January 1872); and Austria-Hungary (1876, but the law was adopted in 1871). Thailand did not formally adopt the metric system until 1923, but the Royal Thai Survey Department used it for cadastral survey as early as 1896. Denmark and Iceland adopted the metric system in 1907.

Chronology and status of conversion by country

Countries by current metrication status (2016):

  Complete

  Almost complete

  Partially complete

  Little adoption

Links in the country point to articles about metrication in that country.

Year official metrication process started	Country	Previous system of measure	Status of metrication
1795	France	French	5Complete
1814	Portugal	Portuguese	5Complete
1820	Belgium	Various	5Complete
1820	Netherlands	Dutch	5Complete
1848	Chile	Spanish	3Almost entirely complete
1852	Mexico	Variants of Spanish	4Complete (some national and regional units are still in use and some United States customary units also in use in some industries)
1852	Spain	Spanish	4Complete
1861	Italy	Various	5Complete
1862	Brazil	Portuguese	4Complete, but some non-metric units are used for specific areas: rural land – alqueire; cattle weight – arroba; screen sizes – polegada; tyre pressure – libra-força por polegada quadrada, but referred by its English abbreviation: psi.
1862	Peru	Spanish	3Almost entirely complete
1863	Uruguay	Spanish	5Complete
1863	Argentina	Spanish	5Complete
1864	Romania	Romanian	5Complete
1868	North German Confederation	Various	5Complete
1869	South German states	Various	5Complete
1871	Austria	Various	5Complete
1872	Germany	Various	5Complete; informally, the Pfund (pound) of 500 g is still used for buying bread and meat, though weight tags are in grams.
1873	Serbia	Various	5Complete
1874	Hungary	Hungarian	5Complete
1875	Ottoman Empire/Turkey	Ottoman	5Complete
1875	Norway	Norwegian	5Complete
1876	Sweden	Swedish	4Complete; the old unit of length mil, redefined in 1876 as 10 km, is however still in everyday use, including that fuel consumption for motor vehicles is always given as "liter per mil", both in everyday speech and in advertising; in some contexts, such as calculating cost of ownership of a vehicle ("milkostnad", i.e. cost per mil) and reimbursement for using a privately owned vehicle instead of a company car ("milersättning"), the mil is even still used in legal texts, despite officially not being a legal unit of length.
1876	Switzerland	Various	5Complete
1886	Finland	Finnish	5Complete
1899	Paraguay	Variants of Spanish	5Complete
1907	Denmark	Danish	5Complete
1907	Iceland	Icelandic / Danish	5Complete
1907	Philippines	Spanish, US customary and local	3Almost entirely complete, English customary units still in use for body measurements
1908	Costa Rica	Spanish	5Complete
1912	Dominican Republic	Spanish	5Complete
1918	Russia	Russian	5Complete
1923	Thailand	Various	3Almost entirely complete
1924	Japan	Japanese	4Complete, with continued informal use of the gō serving size, tsubo of floorspace, &c.
1925	China	Chinese	3Almost entirely complete
1929	Estonia	Estonian	5Complete
1946	Indonesia	Various	3Almost entirely complete
1948	Israel	Ottoman	5Complete
1954	India	Various	5Complete
1954	Sudan	Various	5Complete
1959	Greece	Ancient Greek	5Complete
1961	South Korea	Korean	4Complete, with continued informal use of the pyeong of floorspace
1963	Laos	Unknown	5Complete
1963	Vietnam	Vietnamese	5Complete
1965	United Kingdom	Imperial	2Partially complete
1967	Ireland	Imperial, Irish measure prior to 1824.	3Almost entirely complete. Pint still legal for beer and cider sold in glasses in pubs (only); troy ounce for precious metals also legal. Imperial still in everyday use for body measurements. Some Imperial-size packages persist, with metric labels (e.g. "454 g" label rather than "1 lb").
1967	Pakistan	Imperial	5Complete
1969	New Zealand	Imperial	5Complete
1970	Australia	Imperial	5Complete
1971	South Africa	Imperial	5Complete
1972	Malaysia	Imperial and Malay	Almost entirely complete, with some traditional wet markets and pasar pagi still using the Malay units. Imperial units are widely used such as size of the real estate are often denoted by square feet rather than square metres.
1973	Canada	Imperial	Almost entirely complete (body measurements are referred to in Imperial units, and certain industries such as real estate, construction, and home appliances still use imperial measurements due to a high reliance on American manufacturing.)
1975	United States of America	United States customary units	1Partial adoption (science fields mainly use metric, NASA switched to metric-only in 2007, many bottles of wine are sold in 750 mL, US military uses metric-only, products are dual-labelled, 5K races stand for 5 kilometres, most food nutrition labels are metric-only)
1975	North Korea	Korean	2Partially complete, with formal continued use of traditional units
1975	Ghana	Imperial	5Complete
1976	Sri Lanka	Imperial	3Almost entirely complete
1976	Hong Kong	Imperial, Chinese	3Almost entirely complete (wet markets still use the Chinese units or Imperial units, and real estates still use square foot as area measurement unit.)
1984	Taiwan	Taiwanese	3Almost entirely complete (traditional wet markets and real estate still use Taiwanese units.)
1992	Macau	Imperial, Chinese (Also United States customary units)	3Almost entirely complete
1998	Jamaica	Imperial	3Almost entirely complete, with informal use of Imperial units in rural communities.
2005	Saint Lucia	Imperial	5Complete
Indeterminate	Liberia	Imperial	1Some adoption
2011 2013	Myanmar	Burmese	1 Partial adoption Announcement of full metrication, with technical assistance from the German National Metrology Institute Distances and speed limits on road signs are now shown in kilometers, and height clearance signs are now shown in meters; fuel is now measured and sold in liters; and metorological data and weather reports are now shown in Celsius for temperatures, mm for precipitation levels and kilometers per hour for wind speed.

Notes

There are three common ways that nations convert from traditional measurement systems to the metric system. The first is the quick, or "Big-Bang" route which was used by India in the 1960s and several other nations including Australia and New Zealand since then. The second way is to phase in units over time and progressively outlaw traditional units. This method, favoured by some industrial nations, is slower and generally less complete. The third way is to redefine traditional units in metric terms. This has been used successfully where traditional units were ill-defined and had regional variations.

The "Big-Bang" way is to simultaneously outlaw the use of pre-metric measurement, metricate, reissue all government publications and laws, and change education systems to metric. India's changeover lasted from 1 April 1960, when metric measurements became legal, to 1 April 1962, when all other systems were banned. The Indian model was extremely successful and was copied over much of the developing world.

The phase-in way is to pass a law permitting the use of metric units in parallel with traditional ones, followed by education of metric units, then progressively ban the use of the older measures. This has generally been a slow route to metric. The British Empire permitted the use of metric measures in 1873, but the changeover was not completed in most Commonwealth countries until the 1970s and 1980s when governments took an active role in metric conversion. Japan also followed this route and did not complete the changeover for 70 years. In the United Kingdom, the process is still incomplete. By law, loose goods sold with reference to units of quantity have to be weighed and sold using the metric system. In 2001, the EU directive 80/181/EEC stated that supplementary units (imperial units alongside metric including labelling on packages) would become illegal from the beginning of 2010. In September 2007, a consultation process was started which resulted in the directive being modified to permit supplementary units to be used indefinitely.

The third method is to redefine traditional units in terms of metric values. These redefined "quasi-metric" units often stay in use long after metrication is said to have been completed. Resistance to metrication in post-revolutionary France convinced Napoleon to revert to mesures usuelles (usual measures), and, to some extent, the names remain throughout Europe. In 1814, Portugal adopted the metric system, but with the names of the units substituted by Portuguese traditional ones. In this system, the basic units were the mão-travessa (hand) = 1 decimetre (10 mão-travessas = 1 vara (yard) = 1 metre), the canada = 1 litre and the libra (pound) = 1 kilogram. In the Netherlands, 500 g is informally referred to as a pond (pound) and 100 g as an ons (ounce), and in Germany and France, 500 g is informally referred to respectively as ein Pfund and une livre ("one pound"). In Denmark, the re-defined pund (500 g) is occasionally used, particularly among older people and (older) fruit growers, since these were originally paid according to the number of pounds of fruit produced. In Sweden and Norway, a mil (Scandinavian mile) is informally equal to 10 km, and this has continued to be the predominantly used unit in conversation when referring to geographical distances. In the 19th century, Switzerland had a non-metric system completely based on metric terms (e.g. 1 Fuss (foot) = 30 cm, 1 Zoll (inch) = 3 cm, 1 Linie (line) = 3 mm). In China, the jin now has a value of 500 g and the liang is 50 g.

It is difficult to judge the degree to which ordinary people change to using metric in their daily lives. In countries that have recently changed, older segments of the population tend to still use the older units. Also, local variations abound in which units are round metric quantities or not. In Canada, for example, ovens and cooking temperatures are usually measured in degrees Fahrenheit and Celsius. Except for in cases of import items, all recipes and packaging include both Celsius and Fahrenheit, so Canadians are typically comfortable with both systems of measurement. This extends to manufacturing, where companies are able to use both imperial and metric units, since the major export market is the US, but metric is required for both domestic use and for nearly all other exports. This may be due to the overwhelming influence of the neighbouring United States; similarly, many Canadians still often use non-metric measurements in day-to-day discussions of height and weight, though most driver's licences and other official government documents record weight and height only in metric (Saskatchewan driver licences, prior to the introduction of the current one-piece licence, indicated height in feet and inches but have switched to centimetres following the new licence format). In Canadian schools, however, metric is the standard, except when it comes up in recipes, where both are included, or in practical lessons involving measuring wood or other materials for manufacturing. In the United Kingdom, degrees Fahrenheit are seldom encountered (except when some people talk about hot summer weather), while other metric units are often used in conjunction with older measurements, and road signs use miles rather than kilometres. Another example is "hard" and "soft" metric: Canada converted liquid dairy products to litre, 500 mL, and 250 mL sizes, which caused some complaining at the time of the conversion, as a litre of milk is slightly over 35 imperial fluid ounces, while the former imperial quart used in Canada was 40 ounces. This is an example of a "hard" metric conversion. Conversely, butter in Canada is sold primarily in a 454 g package, which converts to one Imperial pound. This is considered a "soft" metric conversion.

In Ireland, metric is the official unit of measurement though most people would not understand metric units for measuring the body, distances or area. Conversely British imperial units would generally not be understood for temperature. For non-body weights, metric is gradually replacing imperial in everyday use, possibly due to weights on packaging being in metric.

Exceptions

Precious metals, such as gold, are often measured in troy ounces.

As of 2019, the metric system officially predominates in most countries of the world; some traditional units, however, are still used in many places in specific industries. For example:

• Photo and video cameras are standardized to mount to tripods using 1⁄4-20 and 3⁄8-16 screws, which are dimensioned in inches, as per ISO 1222:2010.
• Automobile tyre pressure is commonly measured in units of psi in several countries including Argentina, Australia, Brazil, Chile, Mexico, Peru, Chile, the United Kingdom, and the United States.
• Automotive engine power is usually measured in horsepower (rather than in kilowatts) in Russia, most other ex-USSR countries and German-speaking countries (note that this is typically "metric horsepower" rather than imperial horsepower), although in the EU from 2010 the horsepower is permitted only as a supplementary unit.
• In Hong Kong, traditional Chinese and British imperial units are normally used instead of metric units in particular types of trade.
• Construction workers in Northern Europe often refer to planks and nails by their old inch-based names.
• The length of small sail boats is often given in feet in popular conversation.
• Office space is often rented in traditional units, such as square feet in Hong Kong and India, tsubo/pyeong/"ping" in Japan, Korea, and Taiwan.

A shower hose sold in Germany with metric length (150 cm) and imperial (1⁄2-inch) fittings.

• In plumbing, some pipes and pipe threads are still designated in inch sizes due to historic international acceptance of particular sequences of pipe sizes and pipe threads, such as BSP / ISO 7 / EN 10226 threads.
• In the United Kingdom and some Commonwealth countries, temperatures of domestic gas ovens are often specified using gas marks. Similarly, older French ovens and recipes book often use a scale based on the Fahrenheit scale: "Thermostat" (abbreviated "Th"), where Thermostat 1 equals 100 °F for conventional ovens, increasing by 50 °F for each whole number along the scale.
• Automotive and bicycle wheel diameters are still usually but not always set as whole inch measurements (although tyre widths are measured in millimetres).
• Dots per inch and pixels per inch continue to be used in describing graphical resolution in the computer and printing industry.
• Thread count is frequently measured in "threads per inch" or "ends per inch".
• Television and monitor screen diagonals are still commonly cited in inches in many countries; however, in countries such as Australia, France and South Africa, centimetres are often used for television sets, whereas CRT computer monitors and all LCD monitors are measured in inches.
• Many large format computer printers, commonly known as plotters, have carriage widths measured in inches. Common widths are 24 in (610 mm), 36 in (910 mm), 44 in (1,100 mm) and 60 in (1,500 mm). While metric media sizes are often quoted (e.g. A0, A1), rolls of film, plain paper or photographic paper are normally sold in these widths, giving rise to wastage when they are trimmed. Rolls lengths are variously quoted in feet or metres.
• In the electronic industry, the dominant spacing for components is based on intervals of 1⁄10 in (2.54 mm), and a change would lead to compatibility issues, e.g., for connectors.
• Within the mechanical industry, inch-based spare parts can occasionally be kept, e.g., to service American or pre-World War II machines, but at maintenance, screws may be exchanged to metric thread.
• In Ireland, the only legal exception to the metrication process was the pint (redefined as 570 ml) in bars, pubs, and clubs (although alcohol sold in any other location is in metric units (usually 330 ml (bottled beer), 500 ml (canned beer), 750 ml (wine), or 1 L or 700 ml (spirits))).
• In Australia, a pint of beer was redefined to 570 ml (see Australian beer glasses).
• In both metric and non-metric countries, racing bicycle frames are generally measured in centimetres, while mountain bicycle and other frames are measured in either or both.
• In the sport of surfing, surfboards are usually designed, constructed, and sold in feet and inches.
• In Philippines certain pre-metric units are still used, e.g., the quiñón for land measurement .
• In many long-time metric countries, when non-metric units are used, it is often to give rough estimates in a short form, while accurate measures always are metric, e.g., "6 feet" may feel less exact and shorter to say than "1.8 metres" or "180 cm". Measurement tools for inches are generally rare to find there, only on the other side of some carpenter's rulers, and may present a variation between national legacy inches and British/US inches, easily causing significant measurement errors if used.
• The Imperial gallon is used as a unit of measure for fuel in Anguilla, Antigua and Barbuda, Burma, the Cayman Islands, Dominica, Grenada, Montserrat, St Kitts and Nevis and St Vincent and the Grenadines. In the United Kingdom fuel efficiency is officially recorded in miles per imperial gallon although fuel is sold in litres.
• The US gallon is used in the Bahamas, Belize, British Virgin Islands, Colombia, Dominican Republic, Ecuador, El Salvador, Guatemala, Haiti, Honduras, Liberia, Peru, Turks and Caicos Islands, and the US, especially for pricing.
• In Latin America, as SI units are standard, litres are used as well, e.g., often regarding fuel economy (km per litre), and the Spanish word galón may occasionally refer to a portable fuel container, often 5–20 L
• Road distances and speed limits are still displayed in miles and miles per hour respectively in the USA, UK, Burma, and various Caribbean nations.
• Precious metals are often sold by troy weight, even in countries that otherwise use the metric system.
• Heating, air conditioning, and gas-fuelled cooking appliances often specify their capacity in British thermal units per hour (BTUs/h), even in countries that use neither pounds nor Fahrenheit.

In some countries (such as Antigua and Barbuda, see above), the transition is still in progress. The Caribbean island nation of Saint Lucia announced metrication programmes in 2005 to be compatible with CARICOM.

United Kingdom

See also: Metrication in the United Kingdom

In the United Kingdom, some of the population continue to resist metrication to varying degrees. The traditional imperial measures are preferred by a majority and continue to have widespread use in some applications. The metric system is used by most businesses, and is used for most trade transactions. Metric units must be used for certain trading activities (selling by weight or measure for example), although imperial units may continue to be displayed in parallel.

British law has enacted the provisions of European Union directive 80/181/EEC, which catalogues the units of measure that may be used for "economic, public health, public safety and administrative purposes". These units consist of the recommendations of the General Conference on Weights and Measures, supplemented by some additional units of measure that may be used for specified purposes. Metric units could be legally used for trading purposes for nearly a century before metrication efforts began in earnest. The government had been making preparations for the conversion of the Imperial unit since the 1862 Select Committee on Weights and Measures recommended the conversion and the Weights and Measures Act of 1864 and the Weights and Measures (Metric System) Act of 1896 legalised the metric system. In 1965, with lobbying from British industries and the prospects of joining the Common Market, the government set a 10-year target for full conversion, and created the Metrication Board in 1969. Metrication did occur in some areas during this time period, including the re-surveying of Ordnance Survey maps in 1970, decimalisation of the currency in 1971, and teaching the metric system in schools. No plans were made to make the use of the metric system compulsory, and the Metrication Board was abolished in 1980 following a change in government.

The United Kingdom avoided having to comply with the 1989 European Units of Measurement Directive (89/617/EEC), which required all member states to make the metric system compulsory, by negotiating derogations (delayed switchovers), including for miles on road signs and for pints for draught beer, cider, and milk sales.

Following the United Kingdom's referendum to exit the European Union, retailers have begun to request to go back to using imperial units, with some reverting without permission. A poll following the EU vote also found that 45% of Britons sought to revert to selling produce in imperial units.

Imperial units remain in common everyday use for human body measurements, in particular stones and pounds for weight, and feet and inches for height.

United States and Canada

See also: Metrication in the United States and Metrication in Canada

A measuring cup, manufactured and sold in the United States (circa 1980) features graduations in both metric and US customary systems. Held in the right hand, a person would have the metric graduations in front, facing them. But in filling the measuring cup from another container, right-handed people would hold it in their left hand, and read from the customary graduations.

Over time, the metric system has influenced the United States through international trade and standardisation. The use of the metric system was made legal as a system of measurement in 1866 and the United States was a founding member of the International Bureau of Weights and Measures in 1875. The system was officially adopted by the federal government in 1975 for use in the military and government agencies, and as preferred system for trade and commerce. Attempts in the 1990s to make it mandatory for federal and state road signage to use metric units failed and it remains voluntary.

A 1992 amendment to the Fair Packaging and Labeling Act (FPLA), which took effect in 1994, required labels on federally regulated "consumer commodities" to include both metric and US customary units. As of 2013, all but one US state (New York) have passed laws permitting metric-only labels for the products they regulate. Likewise, Canada also legally allows for dual labelling of goods provided that the metric unit is listed first and that there is a distinction of whether a liquid measure is a US or a Canadian (Imperial) unit.

After many years of informal or optional metrication, the American public and much of the private business and industry still use US customary units today. At least two states, Kentucky and California, have even moved towards demetrication of highway construction projects.

Air and sea transportation

Air and sea transportation commonly use the nautical mile. This is about one minute of arc of latitude along any meridian arc and it is precisely defined as 1852 metres (about 1.151 statute miles). It is not an SI unit (although it is accepted for use in the SI by the BIPM). The prime unit of speed or velocity for maritime and air navigation remains the knot (nautical mile per hour).

The prime unit of measure for aviation (altitude, or flight level) is usually estimated based on air pressure values, and in many countries, it is still described in nominal feet, although many others employ nominal metres. The policies of the International Civil Aviation Organization (ICAO) relating to measurement are:

• there should be a single system of units throughout the world
• the single system should be the SI
• the use of the foot for altitude is a permitted variation.

Consistent with ICAO policy, aviation has undergone a significant amount of metrication over the years. For example, runway lengths are usually given in metres. The United States metricated the data interchange format (METAR) for temperature reports in 1996, and now indicates temperature in Celsius. Metrication is also gradually taking place in cargo weights and dimensions and in fuel volumes and weights.

In some countries like China, ex Soviet countries and Russia, the metric system is used in aviation (whereby in Russia altitudes above the transition level are given in feet). Sailplanes use the metric system in many European countries.

In 1975, the assembly of the International Maritime Organization (IMO) decided that future conventions of the International Convention for the Safety of Life at Sea (SOLAS) and other future IMO instruments should use SI units only.

Accidents and incidents

Confusion over units during the process of metrication can sometimes lead to accidents. In 1983, an Air Canada Boeing 767, nicknamed the "Gimli Glider" following the incident, ran out of fuel in midflight. The incident was caused, in a large part, by the confusion over the conversion between litres, kilograms, and pounds, resulting in the aircraft receiving 22,300 pounds of fuel instead of the required 22,300 kg.

While not strictly an example of national metrication, the use of two different systems was a contributing factor in the loss of the Mars Climate Orbiter in 1999. The National Aeronautics and Space Administration (NASA) specified metric units in the contract. NASA and other organisations worked in metric units, but one subcontractor, Lockheed Martin, provided thruster performance data to the team in pound force-seconds instead of newton-seconds. The spacecraft was intended to orbit Mars at about 150 kilometres (93 mi) in altitude, but the incorrect data meant that it descended to about 57 kilometres (35 mi). As a result, it burned up in the Martian atmosphere.

See also

• Anti-metrication
• Change management, a field studying how changes can be efficiently implemented in modern communities
• Conversion of units
• Language reform
• Preferred numbers
• Spread of the Latin script