Alternator

File:Prokudin-Gorskii-30.jpg

Early 20th century Alternator made in Budapest, Hungary, in the power generating hall of a hydroelectric station.

An alternator is an electromechanical device that converts mechanical energy to alternating current electrical energy. Most alternators use a rotating magnetic field but linear alternators are occasionally used. In principle, any AC generator can be called an alternator, but usually the word refers to small rotating machines driven by automotive and other internal combustion engines.

History

Alternating current generating systems were known in simple forms from the discovery of the magnetic induction of electric current. The early machines were developed by pioneers such as Michael Faraday and Hippolyte Pixii. Faraday developed the "rotating rectangle", whose operation was heteropolar. The first public demonstration of a more robust "alternator system" took place in 1886. Large two-phase alternating current generators were built by a British electrician, J.E.H. Gordon, in 1882. Lord Kelvin and Sebastian Ferranti also developed early alternators, producing frequencies between 100 and 300 hertz. In 1891, Nikola Tesla patented a practical "high-frequency" alternator (which operated around 15,000 hertz). After 1891, polyphase alternators were introduced to supply currents of multiple differing phases. Later alternators were designed for varying alternating-current frequencies between sixteen and about one hundred hertz, for use with arc lighting, incandescent lighting and electric motors.

Theory of operation

Alternators generate electricity by the same principle as DC generators, namely, when the magnetic field around a conductor changes, a current is induced in the conductor. Typically a rotating magnet called the rotor turns within a stationary set of conductors wound in coils on an iron core, called the stator. The field cuts across the conductors, generating an electrical current, as the mechanical input causes the rotor to turn.

The rotor magnetic field may be produced by induction (in a "brushless" alternator), by permanent magnets (in very small machines), or by a rotor winding energized with direct current through slip rings and brushes. The rotor magnetic field may even be provided by stationary field winding, with moving poles in the rotor. Automotive alternators invariably use a rotor winding, which allows control of the alternator generated voltage by varying the current in the rotor field winding. Permanent magnet machines avoid the loss due to magnetizing current in the rotor, but are restricted in size, owing to the cost of the magnet material. Since the permanent magnet field is constant, the terminal voltage varies directly with the speed of the generator. Brushless AC generators are usually larger machines than those used in automotive applications.

Automotive alternators

Alternators are used in automobiles to charge the battery and to power a car's electric system when its engine is running. Alternators have the great advantage over direct-current generators of not using a commutator, which makes them simpler, lighter, less costly, and more rugged than a DC generator. The stronger construction of automotive alternators allow them to turn twice as fast as the engine, improving output when the engine is idling. The availability of low-cost solid-state diodes from about 1960 allowed auto manufacturers to substitute alternators for DC generators. Automotive alternators use a set of rectifiers (diode bridge) to convert AC to DC. To provide direct current with low ripple, automotive alternators have a three-phase winding.

Typical passenger vehicle and light truck alternators use Lundell or claw-pole field construction, where the field north and south poles are all energized by a single winding, with the poles looking rather like fingers of two hands interlocked with each other. Larger vehicles may have salient-pole alternators similar to larger machines. The automotive alternator is usually belt driven at 2-3 times the engine crankshaft speed.

Modern automotive alternators have a voltage regulator built into them. The voltage regulator operates by modulating the small field current in order to produce a constant voltage at the stator output. The field current is much smaller than the output current of the alternator; for example, a 70-amp alternator may need only 2 amps of field current.

Efficiency of automotive alternators is limited by fan cooling loss, bearing loss, iron loss, copper loss, and the voltage drop in the diode bridges; at part load, efficiency is between 50-62% depending on the size of alternator, and varies with alternator speed. In comparison, the best permanent magnet generators, such as those used for bicycle lighting systems, achieve an efficiency of around only 60%.

The field windings are initially supplied via the ignition switch and charge warning light, which is why the light glows when the ignition is on but the engine is not running. Once the engine is running and the alternator is generating, a diode feeds the field current from the alternator main output, thus equalizing the voltage across the warning light which goes out. The wire supplying the field current is often referred to as the "exciter" wire. The drawback of this arrangement is that if the warning light fails or the "exciter" wire is disconnected, no priming current reaches the alternator field windings and so the alternator will not generate any power. However, some alternators will self-excite when the engine is revved to a certain speed. The driver may check for a faulty exciter-circuit by ensuring that the warning light is glowing with the engine stopped.

Very large automotive alternators used on busses, heavy equipment or emergency vehicles may produce 300 amperes. Very old automobiles with minimal lighting and electronic devices may have only a 30 ampere alternator. Typical passenger car and light truck alternators are rated around 70 amperes, though higher ratings are becoming more common. Very large automotive alternators may be water-cooled or oil-cooled.

Many alternators are also linked to the vehicles on board computer system, and in recent years many other factors including air flow are considered in adjusting the battery charging voltage supplied by the alternator.

Brushless Alternators

Terminology

The stationary part of a motor or alternator is called the stator and the rotating part is called the rotor. The coils of wire that are used to produce a magnetic field are called the field and the coils that produce the power are called the armature. The coils of wire that are used to create the field and the armature are sometimes referred to as the “windings”.

Construction

A brushless alternator is composed of two alternators built end-to-end on one shaft. Smaller brushless alternators may look like one unit but the two parts are readily identifiable on the large versions. The larger of the two sections is the main alternator and the smaller one is the exciter. The exciter has stationary field coils and a rotating armature (power coils). The main alternator uses the opposite configuration with a rotating field and stationary armature.

Exciter

The exciter field coils are on the stator and its armature is on the rotor. The AC output from the exciter armature is fed through a set of diodes that are also mounted on the rotor to produce a DC voltage. This is fed directly to the field coils of the main alternator, which are also located on the rotor. With this arrangement, brushes and slip rings are not required to feed current to the rotating field coils. This can be contrasted with a simple automotive alternator where brushes and slip rings are used to supply current to the rotating field.

Main Alternator

The main alternator has a rotating field as described above and a stationary armature (power generation windings). With the armature stationary, the high current output does not have to go through brushes and slip rings. Although the electrical design is more complex, it results in a very reliable alternator because the only parts subject to wear are the bearings.

Control System

Varying the amount of current through the stationary exciter field coils controls the strength of the magnetic field in the exciter. This in turn controls the output from the exciter. The exciter output is fed into the rotating field of the main alternator to supply the magnetic field for it. The strength of the magnetic field in the main alternator then controls its output. The result of all this is that a small current, in the field of the exciter indirectly controls the output of the main alternator and none of it has to go through brushes and slip-rings.

AVR

AVR is an abbreviation for Automatic Voltage Regulator. An AVR serves the same function as the “voltage regulator” in an automobile or the “regulator” or “controller” in a home power system.

Hybrid automobiles

Hybrid automobiles replace the separate alternator and starter motor with a combined motor/generator that performs both functions, cranking the internal combustion engine when starting, providing additional mechanical power for accelerating, and charging a large storage battery when the vehicle is running at constant speed. These rotating machines have considerably more powerful electronic devices for their control than the simple automotive alternator described above.

Radio alternators

Main article: Alexanderson alternator

Extending Tesla's work on high-frequency alternators, high frequency alternators of the variable-reluctance type were applied commercially to radio transmission in the low-frequency radio bands. These were used for transmission of Morse code and, experimentally, for transmission of voice and music.kenapasangala vera velai illaya

See also

• Electrical generator as in pre-1960 motor cars
• Linear alternator

References

• Thompson, Sylvanus P., Dynamo-Electric Machinery, A Manual for Students of Electrotechnics, Part 1, Collier and Sons, New York, 1902
• White, Thomas H.,"Alternator-Transmitter Development (1891-1920)". EarlyRadioHistory.us.

Alternators

• "Alternators". Integrated Publishing (TPub.com).
• "Wooden Low-RPM Alternator". ForceField, Fort Collins, Colorado, USA.
• "Understanding 3 phase alternators". WindStuffNow.
• Author unknown, "Alternator secrets". date unknown.
• "Alternator, Arc and Spark. The first Wireless Transmitters". The G0UTY Homepage.
• Tesla, Nikola, "The Ewing High-Frequency Alternator and Parson's Steam Engine". 12-17-1892. (Pepe's Tesla Pages, DOC)
• First practical alternating current with transformers system demonstrated (by William Stanley)